Operator’s Manual
Single Stage
Snow Thrower
Model 721E
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368023 Cleveland, Ohio 44136-9722.
CUB CADET CORP. P.O. BOX 368023 CLEVELAND, OHIO 44136-9722
770-10542
7/11/01
PRINTED IN U.S.A.
FORM NO.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: This symbol points out important safety instructions which, if not followed, could endanger
the personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol—heed its warning.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit
chemicals known to State of California to cause cancer and birth defects or other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type
of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable
of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
6. Disengage all clutch levers before starting the engine.
Training
7. Never attempt to make any adjustments while engine is
1. Read, understand, and follow all instructions on the
running, except where specifically recommended in the
machine and in the manual(s) before attempting to
operator’s manual.
assemble and operate. Keep this manual in a safe place
8. Let engine and machine adjust to outdoor temperature
for future and regular reference and for ordering
replacement parts.
2. Be familiar with all controls and their proper operation.
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely
Know how to stop the machine and disengage them
flammable and the vapors are explosive. Serious
quickly.
personal injury can occur when gasoline is spilled on
3. Never allow children under 14 years old to operate this
yourself or your clothes which can ignite. Wash your skin
machine. Children 14 years old and over should read and
and change clothes immediately.
understand the operation instructions and safety rules in
a. Use only an approved gasoline container.
this manual and should be trained and supervised by a
parent.
4. Never allow adults to operate this machine without
proper instruction.
5. Thrown objects can cause serious personal injury. Plan
b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the
engine is hot or running.
your snow throwing pattern to avoid discharge of material
e. Allow engine to cool at least two minutes before
toward roads, bystanders and the like.
refueling.
6. Keep bystanders, helpers, pets and children at least 75
f. Never over fill fuel tank. Fill tank to no more than
feet from the machine while it is in operation. Stop
½ inch below bottom of filler neck to provide space
machine if anyone enters the area.
for fuel expansion.
7. Exercise caution to avoid slipping or falling, especially
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and
when operating in reverse.
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
Preparation
i. Never store the machine or fuel container inside
1. Thoroughly inspect the area where the equipment is to
where there is an open flame, spark or pilot light
be used. Remove all door mats, newspapers, sleds,
(e.g. furnace, water heater, space heater, clothes
boards, wires and other objects which could be tripped
dryer etc.).
j. Allow machine to cool at least 5 minutes before
2. Always wear safety glasses or eye shields during
storing.
over or thrown by the auger/impeller.
operation and while performing an adjustment or repair to
protect your eyes. Thrown objects which ricochet can
Operation
cause serious injury to the eyes.
3. Do not operate without wearing adequate winter outer
1. Do not put hands or feet near rotating parts, in the auger/
garments. Do not wear jewelry, long scarves or other
impeller housing or discharge chute. Contact with
loose clothing which could become entangled in moving
rotating parts can amputate hands and feet.
parts. Wear footwear which will improve footing on
slippery surfaces.
2. The auger/impeller clutch lever is a safety device. Never
bypass its operation. Doing so, makes the machine
4. Use a grounded three wire extension cord and receptacle
unsafe and may cause personal injury.
for all units with electric start engines.
5. Adjust collector housing height to clear gravel or crushed
3. The clutch levers must operate easily in both directions
and automatically return to the disengaged position when
rock surfaces.
released.
3
4. Never operate with a missing or damaged discharge
chute. Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
6. Do not operate machine while under the influence of
alcohol or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
Maintenance And Storage
1. Never tamper with safety devices. Check their proper
operation regularly.
2. Disengage all clutch levers and stop engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting before cleaning, repairing, or
inspecting.
3. Check bolts, and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original
equipment manufacturer’s (O.E.M.) parts only. “Use of
parts which do not meet the original equipment
specifications may lead to improper performance and
compromise safety!”
6. Check clutch controls periodically to verify they engage
and disengage properly and adjust, if necessary. Refer to
the adjustment section in this operator’s manual for
instructions.
7. Maintain or replace safety and instruction labels, as
necessary.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while
operating on slopes.
10. Plan your snow throwing pattern to avoid discharge
towards windows, walls, cars etc. To avoid property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets
or allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or
light. Always be sure of your footing and keep a firm hold
on the handles. Walk, never run.
14. Disengage power to the auger/impeller when
transporting or not in use.
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when in reverse.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
17. Disengage all clutch levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the discharge chute, making any
adjustments, or inspections.
8. Observe proper disposal laws and regulations for gas,
oil, etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace ,clothes dryer etc.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
18. Never put your hand in the discharge or collector
openings. Always use a clearing tool to unclog the
discharge opening.
Your Responsibility:
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual,
use care and good judgment. Contact your dealer or
telephone 1-800-528-1009 for assistance and the name
of your nearest servicing dealer.
•
Restrict the use of this power machine to persons
who read, understand and follow the warnings and
instructions in this manual and on the machine.
A N D C L O T H I N G A W A Y .
K E E P H A N D S , F E E T
R O T A T I N G A U G E R -
A V O I D I N J U R Y F R O M
DANGER
1.
KEEP AWAY FROM ROTATING AUGER
CONTACT WITH AUGER CAN AMPUTATE
HANDS AND FEET.
2. DISENGAGE CLUTCH LEVERS, STOP ENGINE,
AND REMAIN BEHIND HANDLES UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING OR SERVICING MACHINE.
3. TO AVOID THROWN OBJECTS INJURIES,
NEVER DIRECT DISCHARGE AT BYSTANDERS.
USE EXTRA CAUTION WHEN OPERATING ON
GRAVEL SURFACES.
NEVER PUT HAND IN CHUTE. CONTACT WITH
ROTATING PARTS CAN AMPUTATE FINGERS
AND HANDS.
DO NOT UNCLOG DISCHARGE CHUTE WHILE
ENGINE IS RUNNING.
SHUT OFF ENGINE AND REMAIN BEHIND
HANDLES UNTIL ALL MOVING PARTS HAVE
STOPPED BEFORE UNCLOGGING.
4. READ OPERATOR'S MANUAL.
4
SECTION 2: ASSEMBLING YOUR SNOW THROWER
•
•
•
Remove the hairpin clip from the end of the lower
chute crank.
Insert the upper chute crank into the lower chute
crank and align the holes.
Re-insert the hairpin clip into the hole to secure the
two chute cranks. See Figure 2.
Unpacking From Carton
•
•
•
Cut along corners of the carton and lay it down flat.
Remove packing material.
Remove any loose parts included with unit (i.e.,
operator’s manual, etc.).
Roll unit out of carton. Check carton thoroughly for
any remaining loose part.
Items Required For Assembly
1. Pair of pliers
2. Engine oil
3. Fresh gasoline
NOTE: All references to left or right side of the snow
thrower is from the operating position only.
Upper Chute
Crank
Hairpin Clip
Before Assembly
Lower Chute
Crank
WARNING: Disconnect the spark plug wire
and ground it against the engine to prevent
unintended starting. See Figure 1.
NOTE: For clarity
of viewing, the
control handle is
removed from the
picture. Do not
Raising Upper Handle
remove it for the task.
•
Loosen the hand knob on each side of the handle.
Remove packing material, if any.
Figure 2
Attaching Control Cable
The control cable may already be attached to the
control handle. If not attached, complete the following
steps to attach it to the snow thrower housing.
•
Route the control cable over the lower handle.
Insert the end of the cable into the hole in the
control housing as shown in Figure 3. Push the
plastic fitting until it locks into the control housing.
Hand Knob
Hand Knob
“Z” End
Bottom
of Cable
Hole In
Spark Plug
Access
Control
Handle
Figure 1
Control
•
•
Raise the upper handle in the direction shown in
Figure 1 until it clicks into the operating position.
Make sure not to pinch or crimp the cable.
Tighten the hand knobs.
Plastic
Fitting
Housing
Figure 3
Attaching Chute Crank
•
Lift the control handle up, and hook the “Z” end of
the control cable into the bottom hole in the control
handle, from the outside to the inside . If necessary,
pull up on the end of the cable with a pair of pliers to
obtain slack in order to hook it into the control
The lower chute crank is already attached to your snow
thrower at the factory. For shipping purposes, the upper
chute crank is packaged as loose part. Attach it to the
lower chute crank following instructions:
5
handle. Hold the “Z” fitting with the pliers, not the
cable, to avoid damaging the cable.
Lower Chute
Nut
NOTE: The upper hole in the control handle provides
for adjustment in belt tension. Refer to page 9 of this
manual for instructions.
Carriage
Bolt
Flat
Washer
Flat
Washer
Assembling Discharge Chute
Hex Bolt
•
•
•
Turn the chute crank until the chute faces straight
to the front. See Figure 4 .
Remove the hand knob, flat washer and carriage
bolt from the upper chute. See Figure 4.
Pivot the upper chute up and over the lip of the
lower chute. This will eliminate any gap between
the upper and the lower chutes. Secure with
hardware just removed.
Upper
Chute
Hand
Knob
Figure 4
SECTION 3: KNOW YOUR SNOW THROWER
WARNING: Be familiar with all the controls on the snow thrower and their proper operation. Know how to
stop the machine and disengage them quickly.
Auger Control Handle
Recoil Starter
Chute Crank
Primer
Key
Electric Starter
Gasoline Cap
Spark Plug Access
Discharge Chute
Oil Fill Plug
Choke Lever
Off
On
Auger
Shave Plate
Figure 5
Chute Crank
Auger Control Handle
Located on the upper handle, the auger control handle
is used to engage and disengage the auger. The snow
thrower is designed to propell by the rotation of the
auger. Pull the control handle back against the upper
handle to engage the auger; release to disengage.
Located on right side of dash panel, the chute crank
determines the direction that snow will be discharged.
Turn clockwise to discharge snow to the left; turn
counterclockwise to discharge to the right.
6
Discharge Chute
Ignition Key
The angle of the discharge chute controls the distance
that the snow is thrown. Tilt the discharge chute up for
greater distance; tilt down for less distance. Loosen the
hand knob on the side of the discharge chute to adjust.
Tilt the chute to the desired position, and tighten the
knob.
Used to start engine. Put key in “ON” position to start
for both electric and recoil start engines. Follow starting
instructions given in the next section.
Recoil Starter
Used to manually start the engine.
Electric Starter
Used to start engine with a 120V power source.
Choke Lever
Place choke lever in “ON” position to start a cold
engine. This lever is located near the throttle housing
on the engine. See Figure 5 inset.
Plug for Electric Start
Requires use of a three-prong outdoor extension cord
and a 120V power source.
Primer Button
Spark Plug Access
Spark plug located under the access cover.
Used to inject fuel directly into the carburetor to insure
fast starts in cold weather. Follow engine manual to
prime engine.
SECTION 4: OPERATING YOUR SNOW THROWER
Before Starting
Press auger
control handle
to engage
auger
WARNING: Read, understand, and follow all
instructions and warnings on the machine and
in this manual before operating.
Turn handle
•
The spark plug wire was disconnected for safety.
Attach spark plug wire to spark plug before starting.
to change
discharge
direction
Recoil
Starter
Primer
Key
Gas and Oil Fill-Up
•
Check oil and gasoline level and add if necessary.
Follow related instructions in the seperate engine
manual packed with your snow thrower.
Electric
Starter
Choke
Lever
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Never
fuel the machine indoors or while the engine is
hot or running. Extinguish cigarettes, cigars,
pipes and other sources of ignition.
Spark Plug Access
Figure 6
To Start Engine
•
•
•
•
The electric starter is equipped with a grounded
three-wire power cord and plug, and is designed to
operate on 120 volt AC household current.
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
If your home wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but
a three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
•
•
Insert ignition key into slot. Turn key to ON position.
Now follow the instructions below as it pertains to
your unit.
Electric Starter
WARNING: The electric starter must be
used with a properly grounded three-prong
receptacle at all times to avoid the possibility of
electric shock. Follow all instructions carefully
prior to operating the electric starter.
7
•
If you have a grounded three-prong receptacle,
proceed as follows.
Rotate choke lever to FULL position.
Connect power cord to switch box on dash panel.
Plug the other end of power cord into a three-prong
120-volt, grounded, AC receptacle.
Push starter button to crank engine. As you crank
the engine, move choke lever to FULL choke
position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
or four times. Pulling the starter rope will produce a
loud clattering sound, which is not harmful to the
engine or starter.
Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also, move
control levers back and forth several times. Leave
throttle control lever in the STOP or OFF position.
Leave choke control in the FULL choke position.
Remove ignition key and disconnect spark plug
wire to prevent accidental starting.
•
•
•
•
•
•
Operating the Snow Thrower
•
Adjust the upper discharge chute up or down as
shown in Figure 7. You will have to loosen the hand
knob to adjust the upper chute, and then retighten
after correct adjustment is reached.
•
When disconnecting the power cord, always unplug
from the three-prong receptacle first, and then from
the snow thrower.
Recoil Starter
•
•
Use the chute crank to position the discharge chute
in order to discharge snow with the wind.
•
•
•
•
Rotate choke lever to FULL choke position (cold
engine start).
If engine is warm, place choke in OFF position
instead of FULL.
Push primer button two or three times for cold
engine start.
After making sure no bystanders or obstacles are in
front of the unit, engage the auger control handle.
As the snow thrower starts to move, maintain a firm
hold on the handle, and guide the snow thrower
along the path to be cleared.
If engine is warm, push primer button only once.
•
Release the auger control handle to stop the snow
throwing action and the forward motion.
NOTE: Always cover vent hole in primer button when
pushing. Additional priming may be necessary for first
start if temperature is below 15 degrees Fahrenheit.
Upper
Discharge
Chute
•
Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
As engine warms up and begins to operate evenly,
rotate choke lever slowly to OFF position. If engine
falters, return to FULL choke, then slowly move to
OFF position.
•
Hand
Knob
•
Figure 7
To Stop Engine
Operating Tips
•
To stop engine, turn ignition key counter-clockwise.
Disconnect the spark plug wire from the spark plug
to prevent accidental starting while equipment is
unattended.
•
Discharge snow downwind whenever possible.
Slightly overlap each previously cleared path.
Lifting up on the handle will allow the rubber on the
augers to propel the snow thrower forward. Pushing
downward on the handle will raise the augers off
the ground and stop forward motion.
•
To help prevent possible freeze-up of starter, proceed
as follows:
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
NOTE: Excessive upward pressure on the handle will
result in premature wear on the rubber auger blades
which would not be covered by warranty.
•
Electric Starter: Connect power cord to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and spin the
starter for several seconds. The unusual sound
made by spinning the starter will not harm engine or
starter. Disconnect the power cord from receptacle
first, and then from switch box.
•
•
Run the engine for a few minutes before stopping to
help dry any moisture on the engine.
Clean the snow thrower thoroughly after each use.
WARNING: Muffler, engine and surrounding
areas become hot and can cause a burn. Do
not touch.
•
Recoil Starter: With engine running, pull starter
rope with a rapid, continuous full arm stroke three
8
SECTION 5: MAKING ADJUSTMENTS
Belt Tension
WARNING: NEVER attempt to make any
adjustments while the engine is running,
except where specified in the snow thrower
and/or engine operator’s manuals.
Periodic adjustment of the belt tension may be required
due to normal stretch and wear on the belt. Adjust the
belt tension, following instructions below, if the augers
seem to hesitate while turning although engine
maintains the same speed.
Shave Plate
•
The upper hole in the control handle provides
adjustment for belt tension. To adjust, disconnect
the “Z” end of control cable from the bottom hole in
the control handle. See Figure 10 . Hook the cable
into the upper hole in control handle as shown.
•
To check the adjustment of the shave plate, place
the unit on a level surface. See Figure 8. The
wheels, shave plate and augers should all contact
level surface. Note that if the shave plate is
adjusted too high, snow may blow under the
housing. If the shave plate wears out excessively,
or the unit does not self-propel, the shave plate
may be too low and needs to be adjusted.
Upper
Hole
Clutch
Cable
NOTE: On new units or units with a new shave plate
installed, the augers may be slightly off the ground.
Control
Housing
Figure 10
If additional adjustment is required, follow steps below.
•
Remove the belt cover by removing five hex screws
that hold it in place. See Figure 12.
•
There are three adjustment holes provided in the
idler bracket assembly. See Figure 11. To adjust,
move the extension spring on the end of the clutch
cable to the next higher adjustment position on the
idler bracket assembly. Reassemble belt cover.
Augers
Shave Plate
Figure 8
High Position
Middle Position
Idler
Bracket
•
To adjust, tip the snow thrower back so that it rests
on the handle. Loosen the four lock nuts and bolts
which secure the shave plate to the housing. See
Figure 9. Move the shave plate to desired position
and retighten the nuts and bolts securely.
Low Position
Auger
Spring on
Pulley
End of Clutch
Cable
Figure 11
Carburetor
WARNING: If any adjustments need to be
made to the engine while the engine is running
(e.g. carburetor), keep clear of all moving parts.
Be careful of muffler, engine and other
surrounding heated surfaces.
•
Refer to the separate engine manual, packed with
your unit, for carburetor adjustment information.
Lock Nut & Carriage Bolt
Figure 9
9
SECTION 6: MAINTAINING YOUR SNOW THROWER
Replacing Shave Plate
WARNING: Before servicing, repairing, or
inspecting, disengage all clutch levers and stop
engine. Wait until all moving parts have come
to a complete stop. Disconnect spark plug wire
and ground it against the engine to prevent
unintended starting.
The shave plate is attached to the bottom of the auger
housing and is subject to wear. It should be checked
periodically. There are two wearing edges and the
shave plate can be reversed. See Figure 14.
•
•
•
Remove the four carriage bolts and hex lock nuts
which attach it to the snow thrower housing.
Install new shave plate, making sure the heads of
the carriage bolts are on the inside of the housing.
Adjust the shave plate according to instructions on
page 9. Tighten securely.
Replacing Belt
•
Remove the belt cover by removing five hex
screws. See Figure 12.
Hex
Screw
Shave
Plate
Hex Screw
Remove these hardware
Belt Cover
Figure 12
Figure 14
•
•
Pull up on the idler pulley and slip the belt off the
engine pulley.
Push down on the idler pulley and slip the belt off
the auger pulley.
Engine
•
Refer to the separate engine manual for all engine
maintenance procedures.
•
•
Reassemble new belt. See Figure 13.
Reinstall the belt cover.
•
Check engine and snow thrower frequently for
loose hardware, and tighten as needed.
Lubrication
•
Lubricate pivot points on the control handle and the
extension spring at the end of the clutch cable with
a light oil once every season and before storage of
the snow thrower at the end of the season.
Lubricate the flange keepers on the chute crank
once a season with a light oil making sure the crank
rod moves freely. Remove bolts holding the shroud
to the housing, and lift shroud to access the chute
crank bracket.
Idler Pulley
•
Engine
Pulley
Auger
Drive
Belt
Pulley
Figure 13
10
SECTION 7: OFF-SEASON STORAGE
•
•
Follow “Storage” instructions in the Engine Manual.
Store in a clean, dry area. Block the snow thrower
up so it is not resting on the rubber auger blades.
WARNING: Never store engine with fuel in
tank indoors or in enclosed, poorly ventilated
areas where fuel fumes may reach an open
flame, spark or pilot light as on a furnace, water
heater, clothes dryer, or other gas appliance.
NOTE: When storing any type of power equipment in a
poorly ventilated or metal storage shed, care should be
taken to rustproof the equipment, especially springs,
cables and all moving parts.
•
•
Clean snow thrower thoroughly.
Lubricate as instructed above with a light oil.
SECTION 8: TROUBLESHOOTING GUIDE
Problem
Cause
Remedy
Engine fails to start
1. Fuel tank empty, or stale fuel
2. Blocked fuel line
1. Fill tank with clean fresh gasoline.
2. Clean fuel line
3. Key not in ON position
4. Spark plug wire disconnected
5. Faulty spark plug
3. Insert key and turn to ON position
4. Connect wire to spark plug.
5. Clean spark plug, readjust gap, or replace.
6. Prime engine four times.
6. Engine not primed
7. Engine flooded with excessive priming
7. Wait at least ten minutes before starting.
Engine runs erratic
1. Unit running on choke
2. Fuel line blocked, or stale fuel
1. Move choke lever to OFF position.
2. Clean fuel line and fill tank with fresh,
clean gasoline.
3. Water or dirt in fuel system
4. Carburetor out of adjustment
3. Refer to engine manual for remedy.
4. Refer to engine manual for remedy.
Engine overheats
Loss of power
1. Carburetor out of adjustment
1. Refer to engine manual for instruction.
1. Spark plug wire loose
2. Vent in gas cap plugged
1. Connect and tighten spark plug wire.
2. Clear vent.
Excessive vibration
1. Loose parts or damaged auger
1. Stop engine immediately and disconnect
spark plug wire. Check for possible
damage. Tighten all bolts and nuts. Repair
as needed. If the problem persists, take
unit to an authorized service dealer.
Unit fails to self-propel 1. Drive cable out of adjustment
2. Drive belt loose or damaged
1. Adjust drive cable following instructions on
page 9 of this manual.
2. Replace drive cable.
Unit fails to discharge 1. Discharge chute clogged
snow
1. Stop engine immediately and disconnect
spark plug wire. Clean discharge chute
and the auger housing.
2. Foreign object lodged in auger
3. Drive cable not adjusted properly
4. Drive belt loose or damaged
2. Stop engine immediately and disconnect
spark plug wire. Remove object .
3. Adjust drive cable following instructions on
page 9 of this manual.
4. Replace drive belt.
NOTE: For repairs beyond the minor adjustments listed above, call the White Outdoor Customer Dealer Line at
1-(800)-949-4483 for the dealer nearest you. Refer to separate engine manual, packed with your snow
thrower, for engine information.
11
SECTION 9: PARTS LIST FOR MODEL 721E
15
9
6
21
17
14
6
6
21
24
21
23
3
1
8
22
13
10
4
2
20
16
25
7
33
42
11
57
12
35
47
45
48
32
19
18
31
44
26
58
11
35
41
53
49
60
28
42
33
36
59
37
52
5
5
27
29
5
54
50
51
43
49
40
35
56
53
38
34
46
55
39
30
12
Model 721E
Ref. No.
Part No.
Part Description
Ref. No.
Part No.
710-0451
Part Description
Carriage Bolt
684-0174
684-0177
684-0178
684-0192
710-0895
710-1003
710-1882
710-3083
712-0252
712-0429
712-3010
714-0104
714-0507
720-0201A
725-0201
725-2018
726-0100
736-0119
736-0185
736-0225
736-0400
736-0451
7519636
Upper Chute Crank Assemby
Lower Chute Crank Assembly
Bracket Assembly: Mitten Grip
Shroud:Black, 7 Hp. Electric
TT Screw 1/4-15 x 0.75”
B Screw #10-16 x 0.625”
Hex Flange Screw
Hex Bolt 5/16-18 x 1.375”
Jam Nut
1.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
710-0642
710-0773
710-0896
710-1005
711-0848A
712-0116
712-3010
712-3027
731-1033
732-0357A
736-0108
736-0119
736-0176
736-0242
736-0326
736-0329
741-0475
741-0600
746-0910A
748-0234
756-0313
784-5174
784-5175B
784-5176
784-5485
784-5720
684-0196
734-1811
710-1090
TT Screw 1/4-20 x 0.75”
TT Screw 3/8-16 x 0.5”
AB Screw 1/4-14 x 0.625”
B Screw 1/4-14 x 0.5”
Axle Tube
2.
3.
4.
5.
6.
7.
Jam Lock Nut
Hex Nut 5/16-18
Lock Nut
8.
9.
Lock Nut
Shave Plate
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
Hex Nut 5/16-18
Extension Spring
Flat Washer
Cotter Pin
Cotter Pin
Lock Washer
Knob: Chute Crank
Ignition Key
Flat Washer
Beleville Washer
Flat Washer
Switch: Electric Start Key
Push Cap
Lock Washer
Lock Washer
Plastic Bushing
Ball Bearing
Flat Washer
Internal Lock Washer
Flat Washer
Clutch Cable
Shoulder Spacer
Flat Idler
Saddle Washer
Mitten Grip Handle
Spark Plug Access
Upper Handle: Gull Wing
Lower Handle
Bearing Cup
684-0190
749-0711A
749-0796B
710-0167
710-0191
710-0323
710-0352
Bracket: Brake Idler
Belt Cover
Auger Assembly
Chute Crank Bracket
Auger Housing Assembly
Wheel Assembly
Hex Flange Screw
Carriage Screw 1/4-20 x 0.50”
Hex Bolt
Machine Screw
B Screw1/4-14 x 0.375”
NOTE: For painted parts, please refer to the
list of color codes below. Please add the
applicable color code, wherever needed, to the
part number to order a replacement part. For
instance, if a part, numbered 700-xxxx, is
painted Yellow, the part number to order would
be 700-xxxx-0716.
Cub Cadet Yellow: 0716
Powder Black: 0637
13
Model 721E
19
16
24
18
1
15
7
5
11
10
15
8
17
Engine is for reference only
and may not resemble the
engine on your snow thrower.
9
6
13
25
3
21
13
14
23
2
3
4
22
20
Ref. No.
Part No.
Description
Extension Cord
Ref. No.
9.
Part No.
719-0581
Description
629-0236
710-0157
710-0409
710-0502A
710-0751
710-1003
710-3013
712-3006
Spacer
1.
2.
3.
4.
5.
6.
7.
8.
Hex Bolt 5/16-24 x 0.75”
Hex Bolt 5/16-24 x 1.75”
TT Sems Screw
726-0205
731-2005
736-0119
736-0242
736-0329
741-0475
751-0535
751-0540A
751-0603
754-0101A
756-0416B
756-0475
784-0322
784-0323
784-0374
Hose Clamp
Choke Knob
Lock Washer
Beleville Washer
Lock Washer
Plastic Bushing
Fuel Line Hose
Gas Tank
10.
11.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
Hex Screw 1/4-20 x 0.620”
B Screw #10-16 x 0.625”
Hex Screw 1/4-20 x 0.50”
Hex Nut 1/4-20
NOTE: For painted parts, please refer to the
list of color codes below. Please add the
applicable color code, wherever needed, to the
part number to order a replacement part. For
instance, if a part, numbered 700-xxxx, is
painted Yellow, the part number to order would
be 700-xxxx-0716.
Fuel Cap
V-Belt
V-Pulley Half
Pulley
Engine Mount
Support Bracket
Support Plate: Engine Mount
Cub Cadet Yellow: 0716
Powder Black: 0637
14
Model 721E
5
Ref. No.
Part No.
710-0487
Description
Carriage Screw 5/16-18 x 2.0”
Machine Screw
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
710-1270
712-0324
720-0284
720-0295
725-0157
736-0451
746-0883
747-0956
749-0711A
Hex Lock Nut 1/4-20
Hand Knob w/ Wing Nut
Foam Grip
8
Cable Tie
10
Saddle Washer
3
Control Housing
2
Auger Bail
4
Upper Handle: Gull Wing
NOTE: For painted parts, please refer to the list of
color codes below. Please add the applicable color
code, wherever needed, to the part number to order a
replacement part. For instance, if a part, numbered 700-
xxxx, is painted yellow, the part number to order would
be 700-xxxx-0716.
1
6
7
7
4
Cub Cadet Yellow: 0716
Powder Black: 0637
5
Ref. No.
Part No.
710-0276
Description
Carriage Screw: Special
Carr. Bolt 5/16-18 x 0.750”
Hex Screw 1/4-20 x 0.75”
Lock Nut
9
1.
2.
710-0451
710-3015
712-3027
712-3068
720-0284
731-0851A
731-0915B
731-0921
736-0159
10
6
3.
10
4.
Hex Lock Nut
5.
8
4
Hand Knob
6.
Flange Keeper: Chute
Lower Chute
7.
1
2
8.
Upper Chute
9.
Washer
10.
4
7
3
15
MANUFACTURER’S LIMITED WARRANTY FOR:
TWO-YEAR RESIDENTIAL
ONE-YEAR COMMERCIAL
Proper maintenance of your Cub Cadet equipment is the owner’s responsibility. Follow the instructions in your
operator’s manual for correct lubricants and maintenance schedule. Your Cub Cadet dealer carries a
complete line of quality lubricants and filters for your equipment’s engine, transmission, chassis and
attachments.
Riding mowers, lawn tractors, garden tractors, Cub Cadet
attachments and home maintenance products
This limited warranty for residential users, covers any defect in materials or workmanship in your Cub Cadet
equipment for two years from the date of purchase for the first user purchaser. We will replace or repair any
part or parts without charge through your authorized Cub Cadet dealer.
Batteries have a one-year prorated limited warranty with 100% replacement during the first three months.
V-belts for either the traction drive or any attachments are covered for one year only.
Cub Cadet equipment used commercially is warranted for one year only.
(Commercial use is defined as either having hired operators or used for income producing purposes.)
Items not covered
The warranty does not cover routine maintenance items such as lubricants, filters (oil, fuel, air and hydraulic),
cleaning, tune-ups, brake and/or clutch inspection, adjustments made as part of normal maintenance, blade
sharpening, set-up, abuse, accidents and normal wear. It does not cover incidental costs such as transporting
your equipment to and from the dealer, telephone charges or renting a product temporarily to replace a
warranted product.
There is no other express warranty.
How to obtain service
Contact your authorized Cub Cadet servicing dealer who sold you your Cub Cadet equipment. If this dealer is
not available, see the Consumer Yellow Pages under “lawn mowers” for the name of a dealer near you.
If you need further assistance in finding an authorized Cub Cadet servicing dealer, contact:
Cub Cadet Corporation
Post Office Box 368023
Cleveland, Ohio 44136
How does state law apply?
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
|