Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
Two-Stage Snow Thrower — Model WE 26
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO. 769-02601
06/28/2006
PRINTED IN U.S.A.
1
Safety
Labels
WARNING
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before at-
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
HEED ITS WARNING!
A chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is designed
to clear a chute assembly of ice and snow.
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
This item is fastened with a cable tie at the factory. Cut
the cable tie before operating the snow thrower.
WARNING: Never use your
hands to clear a clogged chute
assembly. Shut off engine and
remain behind handles until
all moving parts have stopped
before using the clean-out tool
to clear the chute assembly.
and follow the warnings
and instructions
in this manual
and on the machine.
3
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
2
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Safe
Operation Failure to observe the following safety instructions could result in serious injury or death.
Training
Preparation
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
1. Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires and other foreign objects, which could be tripped over
or thrown by the auger/impeller.
Practices
2. Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect your
eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
3. Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other
loose clothing, which could become entangled in moving
parts. Wear footwear which will improve footing on slippery
surfaces.
WARNING
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
4. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
manual before at-
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
HEED ITS WARNING!
e. Allow engine to cool at least two minutes before refuel-
ing.
Your Responsibility
Restrict the use
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
of this power machine
to persons who read,
understand
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip-
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
and follow the warnings
and instructions
in this manual
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least 5 minutes before storing.
and on the machine.
4
Operation
Maintenance & Storage
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
2
2. Before cleaning, repairing, or inspecting machine disen-
gage all control levers and stop the engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
Safe
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
Operation
Practices
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as neces-
sary.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operat-
ing on slopes.
WARNING
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
This symbol points
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
out important safety
instructions, which if
not followed, could
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
11. Always refer to the operator’s manual for proper instructions
on off-season storage. onment.
14. Disengage power to the auger/impeller when transporting or
not in use.
Do not modify engine
15. Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
instructions in this man-
ual before attempting to
operate this machine.
Failure to comply with
these instructions may
result in personal injury.
When you see this
To avoid serious injury or death, do not modify engine in any
way.Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) and Three Way Catalyst (TWC) if so equipped.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
symbol.
HEED IT’S WARNING!
Your Responsibility
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual,
use care and good judgment. Contact your dealer for
assistance.
Your Responsibility
Restrict the use
Restrict the use of this power machine to persons who read, un-
derstand and follow the warnings and instructions in this manual
and on the machine.
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
ꢀ
This Operator’s Manual may cover a range of product
specifications. Characteristics and features discussed
and/or illustrated in this manual may not be applicable to
all models.
3
IMPORTANT: Two replacement auger shear pins are
included with this manual (or stowed in the plastic handle
panel). Refer to “Augers” section in the Maintenance
section for more information regarding shear pin replace-
ment.
Setting Up
Your Snow
Thrower
A
1. Remove the unit from the crate or carton.
2. Observe the lower area of the snow thrower to be
sure both cables are aligned with roller guides before
pivoting handle upward.
B
a. Pull up and back on upper handle as shown in
Figure 1. Align upper handle with the lower handle.
b. Tighten hand knobs securing upper handle to
lower handle.
All references in this
manual to the left or right
side of the snow thrower
is from the operating
position only. Exceptions,
if any, will be specified.
3. Certain units may require assembly of the chute. If this
is the case, follow steps 4-7 to install the chute. If the
chute on the unit is attached, proceed to step 8.
Figure 1
4. Remove wing nut and hex screw from chute control
assembly and clevis pin and cotter pin from chute
support bracket. See Figure 2. Position the chute
assembly (forward-facing) over the chute base.
IMPORTANT: This unit is
shipped with the engine
full of oil. After assembly,
refer to the Tecumseh
Engine manual packed
separately with your
5. Place the 4-way chute control in a centered position.
See Figure 3.
6. Place chute assembly onto chute base and secure
chute control assembly to chute support bracket with
clevis pin and cotter pin removed earlier. See Figure 4.
snow thrower for fuel and
oil fill-up details.
7. Finish securing chute control assembly to chute
support bracket with wing nut and hex screw removed
earlier. See Figure 5.
This Operator’s Manual
may cover a range of
product specifications for
various models. Char-
acteristics and features
discussed and/or
8. Check that all cables are properly routed through the
cable guide on top of the engine. See Figure 6.
9. The extension cord is fastened with a cable tie to the
rear of the auger housing for shipping purposes. Cut
the cable tie and remove it before operating the unit.
illustrated in this manual
may not be applicable to
all models.
Figure 2
Figure 3
Figure 4
6
CAUTION: Prior to operating your
snow thrower, refer to Auger Control
Test in Operation section. Read and
follow all instructions carefully, and
perform all adjustments to verify your snow thrower
is operating safely and properly.
3
Setting Up
Your Snow
Thrower
Shear Pin Storage
Holes are located in the plastic dash panel for convenient
shear pin storage. See Figure 7.
IMPORTANT: This unit is shipped with
the engine full of oil. After assembly,
refer to engine manual for fuel and oil
fill-up details.
Chute Clean-Out Tool
The clean-out tool is conveniently fastened to the rear of
the auger housing with a mounting clip. See Figure 8.
1. Release both the auger control and the drive/auger
control lock.
Figure ꢀ
WARNING
Prior to operating your
snow thrower, refer to
Auger Control Test in
Operation section. Read
and follow all instructions
carefully and perform
all adjustments to verify
your unit is operating
safely and properly.
2. Stop the engine by moving the throttle to the stop
position.
3. Remove the clean-out tool from the mounting clip.
4. Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the chute assembly.
5. Re-fasten the clean-out tool to the mounting clip on
the rear of the auger housing and restart engine.
Figure 6
6. While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow or ice from the
chute assembly before continuing to clear snow.
Never use your hands to
clean snow and ice from
the chute assembly or
auger housing.
WARNING: Never use your hands to
clean snow and ice from the chute
assembly or auger housing.
Tire Pressure
The tires are over-inflated for shipping purposes. Check
the tire pressure before operating the snow thrower. Refer
to the tire side wall for tire manufacturer’s recommended
psi and deflate (or inflate) the tires as necessary. NOTE:
If the tire pressure is not equal in both tires, the unit may
not travel in a straight path and the shave plate may wear
unevenly.
Figure ꢁ
IMPORTANT: Under any
circumstance do not
exceed manufacturer’s
recommended psi. Equal
tire pressure should be
maintained at all times.
Excessive pressure when
seating beads may cause
tire/rim assembly to burst
with force sufficient to
cause serious injury.
Under any circumstance do not exceed manufactur-
er’s recommended psi. Equal tire pressure should
be maintained at all times. Excessive pressure when
seating beads may cause tire/rim assembly to burst
with force sufficient to cause serious injury. Refer to
sidewall of tire for recommended pressure.
Refer to sidewall of tire for
recommended pressure.
Figure 8
ꢁ
KnowYour Snow Thrower
Shift Lever
Drive Control
Four-Way
4
Chute Control™
Auger Control
Operating
Your Snow
Thrower
Electric Start Button
Gas Cap
Chute
Assembly
Oil Fill
Engine Controls
Clean-Out Tool
Recoil Starter
Handle
Electric Starter Outlet
Primer
Ignition
Key
WARNING
Choke
Control
Read, understand, and
follow all instructions and
warnings on the machine
and in this manual before
operating.
Skid Shoe
Throttle
Control
Use extreme care when
handling gasoline.
Figure 12
Now that you have setup your snow thrower, it’s
important to become acquainted with its controls and
features.
Gasoline is extremely
flammable and the vapors
are explosive. Never fuel
the machine indoors or
while the engine is hot
or running. Extinguish
cigarettes, cigars, pipes
and other sources of
ignition.
Choke Control
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the Tecumseh
Engine manual packed separately.
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating the
choke control closes the choke plate on the carburetor
and aids in starting the engine.
Shift Lever
The shift lever is located on the right
side of the handle panel. Place the
shift lever into any of eight positions
to control the direction of travel and
ground speed.
Throttle Control
The throttle control is located on the
engine. It regulates the speed of the
engine and will shut off the engine
when pushed down completely.
Forward
Your snow thrower has six forward (F)
speeds, with position number one (1)
being the slowest speed.
Primer
Depressing the primer forces fuel
directly into the engine’s carburetor to
aid in cold-weather starting.
Reverse
Your snow thrower has two reverse (R)
speeds, with position number one (1)
being the slower speed.
Oil Fill
Engine oil level can be checked and oil
added through the oil fill.
8
Auger Control
Four-Way Chute Control™
4
Operating
Your Snow
Thrower
The chute directional control is located on the left side of
the dash panel.
The auger control is located on the left handle. Squeeze
the control grip against the handle to engage the augers
and start snow throwing action. Release to stop.
•
To change the direction in which snow is thrown,
squeeze the button on the joy-stick and pivot the
joy-stick to the right or to the left.
Drive Control/ Auger Control Lock
•
To change the angle/distance which snow is thrown,
pivot the joy-stick forward or backward.
Ignition Key
The ignition key must be inserted and snapped in place
in order for the engine to start. Remove the ignition key to
prevent unauthorized use of equipment. Do NOT attempt
to turn the key.
WARNING
The operation of any snow
thrower can result in for-
eign objects being thrown
into the eyes, which can
damage your eyes severely.
Always wear safety glasses
while operating the snow
thrower, or while perform-
ing any adjustments or
repairs on it.
Clean-Out Tool
WARNING: Never use your hands to
clear a clogged chute assembly. Shut
off engine and remain behind handles
until all moving parts have stopped
before unclogging.
The drive control is located on the right handle. Squeeze
the control grip against the handle to engage the wheel
drive. Release to stop.
The clean-out tool is mounted to the rear of the auger
housing and is designed to clear a clogged chute. Refer
to the Setup section for instructions on how to properly
use it.
The drive control also locks the auger control so you can
operate the chute directional control without interrupting
the snow throwing process. If the auger control is en-
gaged simultaneously with the drive control, the operator
can release the auger control (on the left handle) and
the augers will remain engaged. Release both controls to
stop the augers and wheel drive.
Be sure no one other than
the operator is standing
near the snow thrower
while starting engine or
operating snow thrower.
Never run engine indoors
or in enclosed, poorly
ventilated areas. Engine
exhaust contains carbon
monoxide, an odorless and
deadly gas. Keep hands,
feet, hair and loose cloth-
ing away from any moving
parts on engine and snow
thrower.
NOTE: This item is fastened with a cable tie to the rear
of the auger housing at the factory. Cut the cable tie
before operating the snow thrower.
IMPORTANT: Always release the drive control before
changing speeds.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
9
6. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to FULL and then slowly into
the OFF position again.
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the Tecumseh Engine manual packed separately with
your snow thrower. Read instructions carefully.
4
7. When disconnecting the extension cord, always unplug
the end at the three-prong wall outlet before unplug-
ging the opposite end from the snow thrower.
Starting The Engine
1. Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over the
metal tip on the spark plug.
Operating
Your Snow
Thrower
Recoil Starter
1. Rotate choke control to FULL choke position (cold
engine start).
2. Make certain both the auger control and drive control
are in the disengaged (released) position.
NOTE: If the engine is already warm, place choke control
in the OFF position instead of FULL.
3. Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
2. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE: The engine cannot start unless the key is
inserted into ignition switch.
Electric Starter
NOTE: DO NOT use primer to restart a warm engine after
a short shutdown.
1. Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
WARNING
Read, understand, and
follow all instructions and
warnings on the machine
and in this manual before
operating.
WARNING: The optional electric
starter is equipped with a grounded
three-wire power cord and plug, and
3. Grasp the recoil starter handle and slowly pull the rope
out. At the point where it becomes slightly harder to
pull the rope, slowly allow the rope to recoil.
is designed to operate on 120 volt AC household
current. It must be used with a properly grounded
three-prong receptacle at all times to avoid the
possibility of electric shock. Follow all instructions
carefully prior to operating the electric starter.
4. Pull the starter handle with a firm, rapid stroke. Do not
release the handle and allow it to snap back. Keep a
firm hold on the starter handle and allow it to slowly
recoil.
Use extreme care when
handling gasoline.
Gasoline is extremely
flammable and the vapors
are explosive. Never fuel
the machine indoors or
while the engine is hot
or running. Extinguish
cigarettes, cigars, pipes
and other sources of
ignition.
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to the FULL position and then
slowly into the OFF position again.
If you have a grounded three-prong receptacle, proceed
as follows:
1. Plug the extension cord into the outlet located on
the engine’s surface. Plug the other end of extension
cord into a three-prong 120-volt, grounded, AC outlet
in a well-ventilated area.
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until it
reaches operating temperatures.
2. Rotate choke control to FULL choke position (for a
cold engine start).
If your home’s wiring
system is not a three-wire
grounded system, do not
use this electric starter
under any conditions.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
Stopping The Engine
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
1. Move throttle control to STOP position.
3. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
2. Remove the ignition key and store in a safe place.
If your home electrical
system is grounded, but
a three-hole receptacle
is not available, do not
use your snow thrower’s
electric starter.
3. Wipe all snow and moisture from the area around the
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
4. Push starter button to start engine.
5. Once the engine starts, immediately release starter
button.
10
To Engage Drive
Auger Control Test
1. With the engine running near top speed, move
shift lever to one of six FORWARD positions or two
REVERSE positions. Select a speed appropriate for
the snow conditions that exist.
Perform the following test before operating your snow
thrower for the first time and at the start of each winter.
Check the adjustment of the auger control as follows:
1. When the auger control is released and in the
disengaged “up” position, the cable should have very
little slack. It should NOT be tight.
4
2. Squeeze drive control against the right handle and
the snow thrower will move. Release it and the drive
motion will stop.
Operating
Your Snow
Thrower
2. In a well-ventilated area, start the snow thrower
engine as instructed on the previous page. Make sure
the throttle is set in the FAST position.
3. To turn the unit left or right, squeeze the respective
wheel steering control. See Figure 12.
3. While standing in the operator’s position (behind the
snow thrower), engage the auger.
To Engage Augers
1. To engage augers and start snow throwing, squeeze
the left hand auger control against the left handle.
Release to stop augers.
4. Allow the auger to remain engaged for approximately
ten (10) seconds before releasing the auger control.
Repeat this several times.
2. While the auger control is engaged, squeeze the drive 5. With the throttle control in the FAST (rabbit) position
and the auger control in the disengaged “up” position,
walk to the front of the machine.
control to move, release to stop. Do not shift speeds
while the drive is engaged.
6. Confirm that the auger has completely stopped
rotating and shows NO signs of motion. If the auger
shows ANY signs of rotating, immediately return to
the operator’s position and shut off the engine. Wait
for ALL moving parts to stop before re-adjusting the
auger control.
NOTE: This same lever also locks auger control so you
can turn the chute control without interrupting the snow
throwing process.
WARNING
The muffler, engine
and surrounding areas
become hot and can cause
a burn. Do not touch.
3. Release the auger control; the interlock mechanism
should keep the auger control engaged until the drive
control is released.
7. To readjust the control cable, loosen the upper hex
nut on the auger cable bracket.
4. Release the drive control to stop both the augers and
the wheel drive. To stop the auger, both levers must
be released.
8. Position the bracket upward to provide more slack (or
downward to increase cable tension). See Figure 13.
9. Retighten the upper hex nut.
10.Repeat Auger Control Test to verify proper adjustment
has been achieved.
When selecting a Drive
Speed, use the slower
speeds until you are
comfortable and familiar
with the operation of the
snow thrower.
NEVER reposition the
shift lever (change speeds
or direction of travel)
without first releasing the
drive control and bringing
the snow thrower to a
complete stop. Doing so
will result in premature
wear to the snow
thrower’s drive system.
Figure 13
11
Shift Cable
If the full range of speeds (forward and reverse) cannot
be achieved, refer to the figure to the left and adjust the
shift cable as follows:
ꢀ
1. Place the shift lever in the fastest forward speed
position.
Making
Adjustments
2. Loosen the hex nut on the shift cable index bracket.
See Figure 14.
3. Pivot the bracket downward to take up slack in the
cable.
4. Retighten the hex nut.
5. Check for correct adjustment before operating the
snow thrower.
Figure 14
Chute Control
Once a season or every 25 hours of operation, whichever
is earlier, check whether the four-way chute control™
cables have slackened. If the chute does not rotate
fully or its pitch cannot be moved up or down, the chute
control cables will have to be adjusted.
WARNING
Read, understand, and
follow all instructions and
warnings on the machine
and in this manual before
operating.
To adjust these cables, proceed as follows:
1. To tighten cable, loosen the top nut and tighten the
bottom nut on the cable.
2. Adjust equally on both sides by working on both
cables. See Figure 15.
Never attempt to make
any adjustments while
the engine is running,
except where specified in
operator’s manual.
Drive Control &
Shift Lever
When the drive control is released and in the disengaged
“up” position, the cable should have very little slack. It
should NOT be tight.
Check the adjustment of the drive control as follows:
1. With the drive control released, push the snow thrower
gently forward. The unit should roll freely.
This Operator’s Manual
may cover a range of
product specifications for
various models. Char-
acteristics and features
discussed and/or
Figure 1ꢀ
2. Engage the drive control and gently attempt to push
the snow thrower forward. The wheels should not turn.
The unit should not roll freely.
illustrated in this manual
may not be applicable to
all models.
3. With the drive control released, move the shift lever
back and forth between the R2 position and the F6
position several times. There should be no resistance
in the shift lever.
4. If any of the above tests failed, the drive cable is in
need of adjustment. Proceed as follows:
5. Loosen the lower hex nut on the drive cable bracket.
See Figure 16.
6. Position the bracket upward to provide more slack (or
downward to increase cable tension).
7. Retighten the lower hex nut.
Figure 16
12
You can also check the adjustment as follows:
1. With the snow thrower tipped forward (be certain to
drain gasoline or place plastic film under the gas cap if
the snow thrower has already been operated), remove
the frame cover underneath the snow thrower by
removing the self-tapping screws. Refer to Figure 22
in Maintenance section.
ꢀ
Making
Adjustments
2. With the drive control released, there must be 1/8"
clearance between the friction wheel and the drive
pulley in all positions of the shift lever.
3. With the drive control engaged, the friction wheel
must contact the drive pulley. Refer to Figure 24 in
Maintenance section.
4. If adjustment is necessary, loosen the lower hex nut
on the drive cable index bracket and pivot the bracket
upward or downward as necessary. Refer to Figure
16. Tighten the lower hex nut to secure the bracket
when correct adjustment is reached.
Figure 1ꢁ
IMPORTANT: It is not
recommended that you
operate this snow thrower
on gravel as loose gravel
can be easily picked up
and thrown by the auger
causing personal injury
or damage to the snow
thrower.
5. Reassemble the frame cover and turn the unit back to
its operating position.
NOTE: If you placed plastic under the gas cap, be certain
to remove it now.
Skid Shoes
The space between this shave plate and the ground can
be adjusted. For close snow removal, place skid shoes in
the low position. Use middle or high position when area to
be cleared is uneven.
If for some reason, you
have to operate the snow
thrower on gravel, keep
the skid shoe in the high-
est position for maximum
clearance between the
ground and the shave
plate.
1. Adjust skid shoes by loosening the four hex nuts,
washers, and carriage bolts and moving skid shoes to
desired position. See Figure 17.
2. Make certain the entire bottom surface of skid shoes
are against the ground to avoid uneven wear on the
skid shoes.
3. Tighten nuts and bolts securely.
Auger Control
To adjust the auger control, refer to the section in this
manual titled “Operating Your Snow Thrower”.
13
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine maintenance.
6
Lubrication
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine lubrication instruc-
tions.
Maintaining
Your Snow
Thrower
Gear Shaft
The gear (hex) shaft should be lubricated at least once
a season or after every 25 hours of operation.
1. Remove the lower frame cover by removing the two
screws which secure it.
2. Apply a light coating of an all-weather multi-purpose
grease to the hex shaft. See Figure 8.
Figure 8
Wheels
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive grease
before reinstalling wheels.
WARNING
Chute Directional Control
Once a season, the joystick should be lubricated with
petroleum jelly, linseed oil, mineral oil, paraffin wax or
3-in-1 oil.
Before lubricating,
repairing, or inspect-
ing, disengage all
controls and stop
engine. Wait until all
moving parts have
come to a complete
stop.
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 9.
Gear Case
The auger gear case has been filled with grease at the
factory. If disassembled for any reason, lubricate with
two ounces of grease (Part Number 737-0168).
Figure 9
NOTE: Do not overfill the gear case. Damage to the
seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
Avoid oil spillage on
rubber friction wheel
and aluminum drive
plate.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
To remove skid shoes:
Do not overfill the gear
case. Damage to the
seals could result.
1. Remove the four carriage bolts and hex flange nuts
which secure them to the snow thrower.
2. Reassemble new skid shoes with the four carriage
bolts (two on each side) and hex flange nuts. Refer
to Figure 10.
To remove shave plate:
1. Remove the carriage bolts and hex nuts which
attach it to the snow thrower housing.
Figure 10
2. Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
14
Auger Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
6
NOTE: Drain the gasoline from the snow thrower, or
place a piece of plastic under the gas cap.
Maintaining
Your Snow
Thrower
2. Carefully pivot the snow thrower up and forward so
that it rests on the auger housing. Remove the frame
cover from the underside of the snow thrower by
removing four self-tapping screws which secure it.
3. Roll the auger belt off the engine pulley.
4. a. Loosen and remove the shoulder screw which
acts as a belt keeper.
2
b. Unhook the support bracket spring from the
frame.
5. Remove the belt from around the auger pulley, and
slip the belt between the support bracket and the
auger pulley. Reassemble auger belt by following
instructions in reverse order.
NOTE: Although
multi-viscosity oils
(5W30, 10W30 etc.)
improve starting in cold
weather, these multi-
viscosity oils also result
in higher oil consump-
tion when used above
32ºF. Check your snow
thrower’s engine oil
level more frequently to
avoid possible engine
damage from running
low on oil.
NOTE: Do NOT forget to reinstall the shoulder screw
and reconnect the spring to the frame after installing a
replacement auger belt.
3
NOTE: Do not sand-
blast spark plug. Spark
plug should be cleaned
by scraping or wire
brushing and washing
with a commercial
solvent.
4
5
IMPORTANT
NEVER replace the
auger shear pins with
standard pins. Any
damage to the auger
gearbox or other com-
ponents, as a result of
doing so, will NOT be
covered by your snow
thrower’s warranty.
15
Augers
•
The augers are secured to the spiral shaft with two
1
shear pins and cotter pins. If the auger should strike a
foreign object or ice jam, the snow thrower is designed
so that the pins may shear. Refer to Figure 9.
6
•
If the augers will not turn, check to see if the pins have
sheared. One set of replacement shear pins has been
provided with the snow thrower. When replacing pins,
spray an oil lubricant into shaft before inserting new
pins.
Maintaining
Your Snow
Thrower
Drive Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
•
Drain the gasoline from the snow thrower, or place a
piece of plastic under the gas cap.
2
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
NEVER replace
the auger shear
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it.
pins with anything
other than OEM
3. a. Grasp the idler pulley and pivot it toward the right.
b. Roll the auger belt off the engine pulley.
c. Lift the drive belt off engine pulley.
Part No.738-04124
replacement shear
pins. Any damage to
the auger gearbox
or other components
as a result of failing
to do so will NOT be
covered by your snow
thrower’s warranty.
4. Slip the drive belt off the pulley and between friction
wheel and friction wheel disc.
•
Remove and replace belt in the reverse order.
3
4
16
Friction Wheel Removal
If the snow thrower fails to drive with the drive control
engaged, and performing the drive control cable adjust-
ment on page 14 fails to correct the problem, the friction
wheel may need to be replaced. Follow the instructions
below. Examine the friction wheel for signs of wear or
cracking and replace if necessary
1
6
•
Place the shift lever in third Forward (F3) position.
Maintaining
Your Snow
Thrower
•
Drain the gasoline from the snow thrower, or place a
piece of plastic under the gas cap.
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
1. a. Remove the frame cover from the underside of
the snow thrower by removing four self-tapping
screws which secure it.
b. Remove the right-hand wheel by removing the
screw and bell washer which secure it to the axle.
2. Carefully remove the hex nut and washer which
secures the hex shaft to the snow thrower frame and
lightly tap the shaft’s end to dislodge the ball bearing
from the right side of the frame.
When reassembling
the friction wheel as-
sembly, tighten each
screw only one rota-
tion before turning the
wheel clockwise and
proceeding with the
next screw. Repeat
this process several
times to ensure the
plates are secured
with equal force.
3. Carefully position the hex shaft downward and to
the left before carefully sliding the friction wheel
assembly off the shaft.
2
NOTE: If you’re replacing the friction wheel assembly
as a whole, discard the worn part and slide the new part
onto the hex shaft. Follow the steps above in reverse
order to reassemble components. If you’re disassem-
bling the friction wheel and replacing only the rubber
ring, proceed as follows:
4. Remove the four screws which secure the friction
wheel’s side plates together.
•
•
•
Remove the rubber ring from between the plates.
Reassemble the side plates with a new rubber ring.
Slide the friction wheel assembly back onto the hex
shaft and follow the steps above in reverse order to
reassemble components.
NEVER replace
the auger shear
pins with anything
other than OEM
3
4
Part No.738-04124
replacement shear
pins. Any damage to
the auger gearbox
or other components
as a result of failing
to do so will NOT be
covered by your snow
thrower’s warranty.
17
If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last pos-
sibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top
performance from the snow thrower for many more years.
ꢁ
Preparing Engine
Preparing Snow Thrower
NOTE: Refer to the engine manual for more detailed
information on preparing the snow thrower engine for
storage.
•
When storing the snow thrower in an unventilated or
metal storage shed, care should be taken to rustproof
the equipment. Using a light oil or silicone, coat the
equipment, especially any chains, springs, bearings
and cables.
Off-Season
Storage
Short-Term Storage
It is important to prevent gum deposits from forming in
essential fuel system parts of the engine such as the
carburetor, fuel filter, fuel hose, or tank during short-term
storage (15-30 days). To prevent this, treat the fuel
system using a fuel stabilizer.
•
•
•
Remove all dirt from exterior of engine and equipment.
Follow lubrication recommendations.
Store equipment in a clean, dry area.
Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™)
is an acceptable alternative in minimizing the formation
of fuel gum deposits during storage. Add stabilizer to
gasoline in fuel tank or storage container. Always follow
mix ratio found on stabilizer container. Run engine at least
10 minutes after adding stabilizer to allow it to reach the
carburetor.
WARNING
Never store snow thrower
with fuel in tank indoors
or in poorly ventilated
areas, where fuel fumes
may reach an open flame,
spark or pilot light as on
a furnace, water heater,
clothes dryer or
WARNING: Never store snow thrower
with fuel in tank indoors or in poorly
ventilated areas, where fuel fumes may
reach an open flame, spark or pilot
light as on a furnace, water heater, clothes dryer or
gas appliance.
gas appliance.
CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or
methanol) can attract moisture which
leads to separation and formation of
Fuel left in engine during
warm weather deteriorates
and will cause serious
starting problems.
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.
Long-Term Storage
Never use engine or carbu-
retor cleaning products in
the fuel tank or permanent
damage may occur.
To avoid engine problems, the fuel system should be
emptied before storage for 30 days or longer.
WARNING: Fuel left in engine during
warm weather deteriorates and will
cause serious starting problems.
1. Run the engine until the fuel tank is empty and it stops
due to lack of fuel. Do not attempt to pour fuel from the
engine.
WARNING: Never use engine or carbu-
retor cleaning products in the fuel tank
or permanent damage may occur.
2. Remove the spark plug and pour one (1) ounce of
engine oil through the spark plug hole into the cylinder.
Cover spark plug hole with a rag and crank the engine
several times to distribute the oil. Replace spark plug.
18
Remedy
1. Move choke to ON position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
Problem
Engine fails to start
Cause
1. Choke not in ON position.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
8
4. Prime engine as instructed in
“Operating Your Snow Thrower”.
Trouble-
shooting
5. Faulty spark plug.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
6. Blocked fuel line.
7. Safety key not in ignition on engine.
7. Insert key fully into the switch.
1. Unit running on CHOKE.
1. Move choke lever to OFF position.
Engine runs erratic
Engine overheats
2. Blocked fuel line or stale fuel.
2. Clean fuel line; fill tank with clean,
fresh gasoline.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
3. Drain fuel tank. Refill with fresh fuel.
4. Contact Cub Cadet Service Dealer.
This section
addresses minor
service issues.
For further details,
contact your nearest
Cub Cadet service
dealer or call
1. Carburetor not adjusted properly.
1. Loose parts or damaged auger.
1. Contact Cub Cadet Service Dealer.
1. Stop engine immediately and discon-
nect spark plug wire. Tighten all bolts
and nuts. If vibration continues, have
unit serviced by a Cub Cadet Service
Dealer.
Excessive
Vibration
1-877-282-8684.
1. Connect and tighten spark plug wire.
1. Spark plug wire loose.
Loss of power
2. Remove ice and snow from gas cap.
Be certain vent hole is clear.
2. Gas cap vent hole plugged.
3. Contact Cub Cadet Service Dealer.
3. Exhaust port plugged.
1. Drive control cable in need of adjust-
ment.
1. Adjust drive control cable. Refer to
“Making Adjustments”.
Unit fails
to propel itself
2. Drive belt loose or damaged.
1. Chute assembly clogged.
2. Replace drive belt.
1. Stop engine immediately and discon-
nect spark plug wire. Clean chute
assembly and inside of auger housing
with clean-out tool or a stick.
Unit fails
to discharge snow
2. Foreign object lodged in auger.
2. Stop engine immediately and discon-
nect spark plug wire. Remove object
from auger with clean-out tool or a
stick.
3. Auger control cable in need of adjust-
ment.
3. Refer to “Auger Control Test” in
Operation section.
4. Auger belt loose or damaged.
5. Shear pin(s) sheared.
4. Refer to Maintenance section.
5. Replace with new shear pin(s).
19
Model WE26
1
2
38
3
5
15
4
7
17
18
6
16
54
9
53
13
11
10
52
12
59
2
55
22
19
14
55
35
24
21
56
57
56
57
23
37
42
25
36
34
32
42
26
33
43
27
41
28
43
29
30
45
44
48
40
46
20
39
49
49
48
49
46
58
51
31
2
8
50
47
20
1. 731-2643
Clean-Out Tool
31. 790-00138A Bearing Housing
2. 712-04065 Flange Lock Nut
3. 756-0981B Flat Idler Pulley
32. 721-0325
33. 736-3084
Plug
Flat Washer
9
4. 710-0347
Hex Bolt, 3/8-16 x 1.75
34. 715-04021 Dowel Pin
5. 790-00080A Auger Idler Bracket
35. 684-04108 Spiral Assembly- RH
6. 736-0174
7. 738-0281
8. 738-0143
Wave Washer
Shoulder Screw
Shoulder Screw
36. 618-0123
37. 717-0528A Worm Gear, 20T
38. 725-0157 Cable Tie
39. 738-04124A Shear Pin
Reducer Hsg.-RH
Parts List
9. 790-00075 Bearing Housing
10. 726-04012 Push Nut
40. 714-0161
41. 736-0351
42. 721-0179
43. 741-0661A
44. 618-0418
45. 711-04284
Key
11. 712-04063 Flange Lock Nut, 5/16-18
Flat Washer
Oil Seal
12. 741-0309
13. 732-0611
Ball Bearing
Extension Spring
Flange Bearing
Reducer Hsg.- LH
Axle, Auger, 26”
14. 710-0604A Screw, 5/16-18 x 0.625
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684
15. 731-04705
16. 710-0703
17. 731-2635
Chute Adapter
Carriage Screw, 1/4-20 x 0.75
Clean-out Tool Mtg. Bracket
46. 684-04107 Spiral Assembly- LH
47. 714-04040 Bow Tie Cotter Pin
48. 731-04870 Spacer
18. 684-04206 Auger Housing Assembly, 26-inch
19. 712-04064 Flange Lock Nut, 1/4-20
or visit
49. 741-0493A Flange Bushing
find the nearest Cub
Cadet service dealer in
your area.
20. 918-04192
21. 790-00141
22. 710-0451
Gearbox Assembly, 26-inch
Slide Shoe, Stainless
Carriage Bolt
50. 736-0188
51. 741-0245
52. 736-0242
53. 629-0071
Flat Washer
Hex Flange Bearing
Bell Washer
23. 790-00148 Shave Plate, Stainless, 25.66”
24. 684-04057 Impeller Assembly
Extension Cord
54. 746-04230 Auger Clutch Cable
25. 717-04126
26. 721-0327
27. 741-0662
Worm Shaft
Oil Seal
55. 710-04525 Carriage Bolt, 5/16-18 x .750
56. 712-04103
57. 736-04216 Bell Washer, .340 x .872 x .060
58. 737-3000 Drive Lube Fitting
59. 710-1260A Screw, 5/16-18 x 0.75
Hex Nut, 5/16-18
Flange Bearing
28. 718-04071 Thrust Collar
29. 741-0663
30. 710-0642
Flange Bearing
Screw, 1/4-20 x 0.75
21
11
Model WE26
12
1
13
15
3
21
52
6
4
8
5
6
17
7
8
16
14
10
44
18
20
11
19
26
14
43
25
24
39
38
36
23
31
37
32
2
53
22
27
54
33
28
29
A
34
35
30
23
47
45
48
55
42
47
46
56
57
58
A
51
60
49
41
40
50
59
22
1. 684-04106B Handle Engagement Assembly RH
2. 738-04194 Flange Shoulder Screw
3. 731-04894B Lock Plate
31. 710-0224
32. 710-0606
Screw, #10-16 x .500
Hex Screw, 1/4-20 x 1.50
33. 731-04427A Upper Chute
9
4. 711-04287 Pivot Rod
34. 790-00155 Joystick Bracket
5. 735-0199A Rubber Bumper
35. 710-04187 Hi-Lo Screw, 1/4-15 x 0.5
36. 984-04116B 4-Way Chute Control™ Assembly
37. 749-04191 Upper Handle LH
38. 710-04326 Screw, #8-16 x 0.50
39. 732-04219A Clutch Lock Spring
6. 710-04354 Screw, 1/4-20 x.375
7. 731-04896A Clutch Lock Cam
8. 712-04081A Shoulder Nut, 1/4-20
9. 725-04314 Wire Harness (Not Shown)
Parts List
10. 725-1649
11. 720-0274
12. 710-1233
Light Socket
40. 712-3087
41. 714-04040 Bow Tie Cotter Pin
42. 726-0470 Cable Tie
Wing Nut, 1/4-20
Handle Grip
Screw, #10-24 x 0.375
13. 738-04122 Shoulder Screw, 1/4-20 x 1.345
14. 710-04586 Screw, 1/4-20 x 1.625
15. 749-04190 Upper Handle RH
43. 631-04133 Handle Clutch Lock LH Assy
44. 684-04105A Handle Engagement Assembly LH
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684
45. 784-5594
Cable Bracket
16. 710-0449
Carriage Screw, 5/16-18 x 2.25
46. 720-04072 Star Knob
17. 720-04039 Shift Knob
47. 712-04063 Flange Lock Nut, 5/16-18
48. 731-1313C Chute Tilt Cable Guide
49. 711-04469A Clevis Pin
18. 931-05335 Handle Panel (Includes Ref. #19)
19. 731-05324 Lens
or visit
find the nearest Cub
Cadet service dealer in
your area.
20. 725-04213 Lamp
50. 710-1260A Screw, 5/16-18 x 0.75
51. 749-04138 Lower Handle
52. 732-04238 Torsion Spring
21. 631-04134A Handle Clutch Lock RH Assy
22. 725-0157
23. 712-04064 Flange Lock Nut, 1/4-20
24. 732-0193 Compression Spring
Cable Tie
53. 736-0262
Flat Washer
54. 731-04890A Joystick Pulley Cover
25. 790-00203 Shift Lever
26. 790-00248 Panel Bracket
27. 738-04125 Shoulder Screw
55. 710-0262
56. 710-0895
Carriage Bolt, 5/16-18 x 1.50
Hi-Lo Screw, 1/4-15 x .75
57. 710-04071 Carriage Bolt, 5/16-18 x 1.0
58. 731-04861A Lower Chute
28. 746-0605
29. 746-04227A Speed Selector Cable
30. 736-0463 Flat Washer, .25 x .630 x .0515
Cable Barrel Holder
59. 710-0627
Hex Screw, 5/16-24 x .750
60. 684-04162 Chute Support Bracket
23
Model WE26
46
48
55
53 61
50
42
62
B
39
63
45
40
7
60
60
54
59
1
59
49
41
47
57
56
22
B
44
51
53
21
43
5
2
58
23
7
45
67
52
64
69
28
65
34
8
23
24 30
26
16
10
7
20
68
12
70
38
33
4
11
66
30
A
24
15
23
36
2
25
37
1
19
29
26
7
13
14
6
5
A
31
17
9
3
18
30
24
35
27
7
24
1. 656-04025A Disc Assembly, Friction Wheel
2. 684-04153 Friction Wheel Assembly, 5.5 OD
3. 684-04154 Support Bracket, Friction Wheel
4. 684-04156 Shift Assembly, Rod
36. See Chart
Wheel Assembly
37. 731-04873 Spacer, 1.25 x .75 x 3.0
38. 738-04168 Axle, .75 x 22”
9
39. 741-0919
40. 710-0106
41. 710-0191
Ball Bearing
5. 710-0627
6. 710-0788
7. 710-0896
Hex Screw, 5/16-24, .750, Gr5
Screw, 1/4-20, 1.000
Hex Screw, 1/4-20, 1.25, Gr5
Hex Screw, 3/8-24, 1.25, Gr8
Parts List
Screw, 1/4-14 x .625
42. 710-04520 Hex Screw, 5/16-24, 1.25, Gr5
43. 710-0654A Screw, Sems, 3/8-16, 1.00
8. 712-04065 Nut, Flange Lock, 3/8-16, Nylon
9. 712-0413
10. 714-0126
11. 716-0104
12. 716-0136
13. 716-0231
14. 717-04209
15. 717-04230
16. 726-0221
17. 732-0264
18. 736-0242
19. 736-0287
20. 736-04161
Nut, Jam Lock, 5/8-18, Gr5, Nylon
Key, Hi Pro, 3/16 x 3/4 Dia.
E-ring, .500 Dia.
44. 710-1245B
Hex Screw, 5/16-24, .875, Gr8
45. 712-04064 Nut, Flange Lock, 1/4-20, Nylon
46. 726-04012 Nut, Push-on, .25 Dia.
47. 731-04792A Cover, Belt
E-ring, Retaining, .875 Dia.
E-ring, .750 Dia.
48. 732-04308 Spring, Torsion, .850 ID x .354
Hex Shaft, .8125, 7-Tooth
Gear, 80-Tooth
49. 736-0247
50. 736-0119
51. 736-0505
Washer, Flat, .406 x 1.25 x .157
Washer, Lock .3125
To order replacement
parts, call the Customer
Dealer Referral Line at
1-877-282-8684
Speed Nut, .500
Washer, Flat, .34 x 1.50 x .150
Extension Spring
52. 748-04053 Pulley, Adapter, .75 Dia.
Washer, Bell, .340 x .872 x .060
Washer, Flat, .793 x 1.24 x .060
Washer, Flat, .75 x 1.00 x .060
53. 748-04112
Spacer, Shoulder, .317 x .50 x .102
or visit
54. 750-04303 Spacer, .875 ID x 1.185 OD
55. 750-04477 Spacer, .340 x .750 x .360
56. 754-04050 Belt, Auger Drive
57. 754-04088 Belt, Wheel Drive
58. 756-04109 Pulley, Auger Drive, 8.1 x .5
find the nearest Cub
Cadet service dealer in
your area.
21. 738-04164A Pin, Friction Disc
22. 741-04098
Ball Bearing, 30 x 55 x 13
23. 738-04184A Screw, Shoulder, .37 x .105, 1/4-20
24. 738-0924A Screw, 1/4-28, .375
59. 756-04113
60. 756-04179
Pulley, Half, V x 2.600 OD
Pulley, Half, 1/4-V x 1.5 OD
25. 741-0245
26. 741-0563
Bearing, Hex Flange x .75 ID
Bearing, Ball, 17 x 40 x 12
61. 790-00208 Idler Bracket, Wheel Drive
62. 790-00230 Sleeve, Bearing Idler
27. 746-04229 Clutch Cable, Wheel, 44.95”
28. 746-04228 Cable, Speed Selector
63. 750-04571 Spacer, Shoulder, .26 x .79 x .538
64. 735-04054 Rubber, Friction Wheel, 5.5 OD
29. 748-0190
30. 756-0625
Spacer, .508 ID x .75 OD x .68
Roller, Cable
65. 710-0751
66. 732-04311
Hex Screw, 1/4-20, .620, Gr5
Spring, Torsion, .750 ID x .968
31. 790-00096 Front Guide Bracket, Auger Cable
32. 790-00180 Frame
67. 712-04063 Nut, Flange Lock, 5/16-18, Nylon
68. 790-00156 Bracket, Shift Spacer
33. 790-00206A Guide Bracket, Auger Cable
34. 790-00207A Guide Bracket, Drive Cable
35. 790-00226 Cover, Frame
69. 790-00217A Pivot Bracket, Speed Selector
70. 790-00218A Shift Bracket, Speed Selector
Wheel Assembly
634-04148 (Right)
634-04147 (Left)
Wheel Size
15 x 5 x 6
15 x 5 x 6
Rim Only
634-04151A
Tire Only
734-04012
734-04012
Valve Only
734-0255
734-0255
634-04151A
2ꢀ
NOTES
Use this page to make notes and write down important information.
26
MANUFACTURER’S LIMITED COMMERCIAL WARRANTY FOR:
The limited warranty set forth below is given by Cub Cadet LLC with re-
spect to new merchandise used for commercial purposes and purchased
and used in the United States and/or its territories and possessions, and
by MTD Products Limited with respect to new merchandise purchased
and used in Canada and/or its territories and possessions (either entity
respectively, “Cub Cadet”).
c.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
d.
e.
Service completed by someone other than an authorized service
dealer.
Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
Replacement parts that are not genuine Cub Cadet parts.
Transportation charges and service calls.
“Cub Cadet” warrants this product (excluding its normal wear parts as
described below) against defects in material and workmanship for a period
of one (1) year commencing on the date of original purchase and will, at
its option, repair or replace, free of charge, any part found to be defective
in materials or workmanship. This limited warranty shall only apply if
this product has been operated and maintained in accordance with the
Operator’s Manual furnished with the product, and has not been subject
to misuse, abuse, neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril or natural
disaster. Damage resulting from the installation or use of any part, acces-
f.
g.
No implied warranty, including any implied warranty of merchant-
ability of fitness for a particular purpose, applies after the applicable
period of express written warranty above as to the parts as identi-
fied. No other express warranty, whether written or oral, except as
sory or attachment not approved by Cub Cadet for use with the product(s) mentioned above, given by any person or entity, including a dealer
covered by this manual will void your warranty as to any resulting damage. or retailer, with respect to any product, shall bind Cub Cadet. During
the period of the warranty, the exclusive remedy is repair or replace-
Normal wear parts are warranted to be free from defects in material and
ment of the product as set forth above.
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batteries,
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, friction wheels, shave plates, auger spiral rubber and
tires.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Cub Cadet shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a warranted
product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area:
Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or contact
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and their
property arising out of the misuse or inability to use the product.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
This limited warranty does not provide coverage in the following cases:
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited war-
ranty gives you specific legal rights, and you may also have other rights
that vary in different jurisdictions.
a.
b.
The engine or component parts thereof. These items may
carry a separate manufacturer’s warranty. Refer to applicable
manufacturer’s warranty for terms and conditions.
Log splitter pumps, valves, and cylinders have a separate
one- year warranty.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-8ꢁꢁ-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
MANUFACTURER’S LIMITED WARRANTY FOR
The limited warranty set forth below is given by Cub Cadet LLC with
c.
d.
Routine maintenance items such as lubricants, filters, blade
respect to new merchandise purchased and used in the United States, its
possessions and territories, and by MTD Products Limited with respect to
new merchandise purchased and used in Canada and/or its territories and
possessions.
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
Replacement parts that are not genuine Cub Cadet parts.
Service completed by someone other than an authorized service
dealer.
“Cub Cadet” warrants this product against defects in material and
workmanship for a period of three (3) years commencing on the date of
original purchase and will, at its option, repair or replace, free of charge,
any part found to be defective in materials or workmanship. This limited
warranty shall only apply if this product has been operated and maintained
in accordance with the Operator’s Manual furnished with the product, and
has not been subject to misuse, abuse, commercial use, neglect, accident,
improper maintenance, alteration, vandalism, theft, fire, water, or damage
because of other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not approved by
Cub Cadet for use with the product(s) covered by this manual will void
your warranty as to any resulting damage.
e.
f.
g.
Transportation charges and service calls.
No implied warranty, including any implied warranty of merchant-
ability of fitness for a particular purpose, applies after the applicable
period of express written warranty above as to the parts as identi-
fied. No other express warranty, whether written or oral, except as
mentioned above, given by any person or entity, including a dealer
or retailer, with respect to any product, shall bind Cub Cadet. During
the period of the warranty, the exclusive remedy is repair or replace-
ment of the product as set forth above.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batteries,
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, shave plates, auger spiral rubber and tires.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Cub Cadet shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a warranted
product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area:
In the U.S.A.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
To locate the dealer in your area, check your Yellow Pages, or contact
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and their
property arising out of the misuse or inability to use the product.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
This limited warranty does not provide coverage in the following cases:
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
a.
b.
The engine or component parts thereof. These items may
carry a separate manufacturer’s warranty. Refer to applicable
manufacturer’s warranty for terms and conditions.
Log splitter pumps, valves, and cylinders have a separate one
year warranty.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited war-
ranty gives you specific legal rights, and you may also have other rights
that vary in different jurisdictions.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-8ꢁꢁ-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
|