Electrolux Air Cleaner ELAP15 User Manual

airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 1  
AIR CLEANER / PURIFICATEUR D’AIR / PURIFICADOR DE AIRE  
Models ELAP15, ELAP30, ELAP40, ELAP45  
USA & Canada 1-800-896-9756  
EN • FR • SP  
900523673 - UM (Jan. 2014) Printed in China  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 3  
IMPORTANT SAFEGUARDS  
19. Do not use detergent to clean  
the unit.  
Polarized plug  
This appliance has a polarized plug  
(one blade is wider than the other). To  
reduce the risk of electric shock, this  
plug will fit in a polarized outlet only  
one way. If the plug does not fit fully  
into the outlet, reverse the plug and  
reinsert. If it still does not fit, contact a  
qualified electrician. Do not modify the  
plug in any way.  
20. Do not wash and reuse the HEPA  
filter or the High Deodorization Anti-  
Odor Carbon Filter (ELAP40) or the  
Carbon Pre-Filter (ELAP15 and  
ELAP30). These filters are  
non-washable.  
21. Hold the handle on the back of the  
unit to transport. Do not hold by the  
front panel.  
CAUTION  
!
Short cord instructions: Your appliance is fitted with a short power supply  
cord as a safety precaution to prevent personal injury or property damage  
resulting from pulling, tripping or becoming entangled with a longer cord. Do  
not allow children to use or be near this appliance without close adult  
supervision. If an extension cord is used, (1) the marked electrical rating of the  
cord set or extension cord should be at least as great as the electrical rating of  
the appliance, and (2) the cord should be arranged so that it will not drape over  
the countertop or tabletop where it can be pulled on by children or tripped over.  
WARNING  
!
Electrical power: If the electric circuit is overloaded with other appliances, your  
appliance may not operate properly. It should be operated on a separate  
electric circuit from other appliances.  
SAVE THESE INSTRUCTIONS  
Consumer Safety Information  
THIS UNIT IS FOR HOUSEHOLD USE ONLY  
PRODUCT SPECIFICATIONS  
Model numbers . . . . . . . . . . . . . . . . . . .ELAP15D7PW, ELAP30D7PW, ELAP40D8PW, ELAP45D8PW  
Power supply . . . . . . . . . . . . . . . . . . . .120V 60Hz  
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . ELAP15D7PW: BLDC Motor, max power 40W  
ELAP30D7PW: BLDC Motor, max power 60W  
ELAP40D8PW: BLDC Motor, max power 110W  
ELAP45D8PW: BLDC Motor, max power 110W  
Dimensions . . . . . . . . . . . . . . . . . . . . . . ELAP15D7PW: 19" H x 14" W x 9" D  
ELAP30D7PW: 19" H x 16" W x 10" D  
ELAP40D8PW: 22" H x 19" W x 12" D  
ELAP45D8PW: 22" H x 19" W x 12" D  
3
Electrolux Customer Service 1-800-896-9756  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 4  
AIR CLEANER COMPONENTS  
ELAP15  
ELAP40  
A. Front panel  
B. Filter frame  
A. Front panel  
B. High Deodorization Anti-Odor Carbon  
C. Carbon Pre-Filter  
Filter (treated with anti-bacterial coating Cleancel®)  
(treated with anti-bacterial coating Cleancel®)  
C. HEPA filter  
D. HEPA filter  
D. Main body  
E. Main body  
E PlasmaWave® fan  
F. Air outlet  
F. PlasmaWave® fan  
G. Air Outlet  
G. Control panel  
H. Control Panel  
ELAP30  
ELAP45  
A. Front panel  
A. Front panel  
B. Filter frame  
B. Filter Cassette consists of the following:  
B1. Washable Cleancel® Pre-Filter  
(treated with anti-bacterial coating Cleancel®)  
C. Carbon Pre-Filter  
(treated with anti-bacterial coating Cleancel®)  
B2. Washable HEPA filter set  
B3. Filter frame  
D. HEPA filter  
B4. Washable Anti-Odor Carbon Filter  
D. Main body  
E. Main body  
F. PlasmaWave® fan  
G. Air outlet  
E. PlasmaWave® fan  
F. Air outlet  
H. Control panel  
G. Control panel  
4
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 5  
AIR CLEANER FEATURES  
ELAP15, ELAP30, ELAP40, ELAP45  
CAUTION: Fully assemble air filter before  
The HEPA filter captures 99.9% of particles  
and impurities as small as 0.3 microns,  
including smoke, dust, pollen, and other  
allergens. Replace when the CHECK FILTER  
indicator light turns on. PlasmaWave®  
Technology uses positive and negative ions  
to clean the air of harmful pollutants  
using (See air cleaner set-up)  
Note: Features vary according to model.  
Quiet operation  
With a four-speed fan with quiet operation  
that is ideal for nighttime.  
breaking them down and converting them to  
naturally occurring oxygen and hydrogen.  
Air quality sensor  
Built with an air quality sensor that detects  
the presence of various pollutants in the air.  
ELAP45 – 5 stage filtration  
The first stage of filtration consists of a  
®
pre-filter coated with Cleancel. The  
Light sensor  
Cleancel® anti-microbial coating prevents  
the growth of micro organisms. The  
The built-in light sensor detects when the  
room is dark and automatically dims the  
lights of the control panel and lowers the  
fan speed for quiet and energy-efficient  
operation. Once the room is dim, the fan  
does not increase speed despite what  
the air quality sensor detects.  
activated Anti-Odor Carbon Filter  
specializes in absorbing odors such as  
those caused by cigarettes, pets, and  
cooking. The Anti-Odor Carbon Filter will  
also trap gases such as ammonia and  
formaldehyde. The HEPA filter set captures  
99.9% of particles and impurities as small  
as 0.3 microns, including smoke, dust,  
pollen, and other allergens. PlasmaWave®  
Technology uses positive and negative ions  
to clean the air of harmful pollutants  
Automatic air cleaning (AUTO mode)  
The air quality sensor detects the amount  
of impurities in the air and automatically  
adjusts the fan speed accordingly to keep  
your air purified.  
breaking them down and converting them to  
naturally occurring oxygen and hydrogen.  
The Cleancel® Pre-Filter set, HEPA filter and  
Anti-Odor Carbon Filter are washable.  
ELAP15, ELAP30, ELAP40 –  
4 stage filtration  
The Carbon Pre-Filter (High Deodorization  
Anti-Odor Carbon Filter for ELAP40)  
absorbs gases and odors such as those  
generated by cigarette smoke, pets,  
ammonia or cooking. For best performance,  
replace every 3 months (every 12 months for  
High Deodorization Anti-Odor Carbon Filter).  
The Cleancel® anti-microbial coating  
prevents the growth of micro organisms.  
5
Electrolux Customer Service 1-800-896-9756  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 6  
CONTROL PANEL  
ELAP15, ELAP30, ELAP40, ELAP45  
I. Air Quality Sensor: Automatically monitors the air quality level and  
adjusts fan speed accordingly when in “AUTO.”  
J. Reset: Resets the “Check Filter” indicator light.  
K. Check Filter Indicator: Signals when to replace filters.  
L. Auto: Automatically adjusts the fan speed according to the amount  
of impurities.  
®
M. PlasmaWave : Shows that the technology is active.  
N. Air Quality Indicator: Lights indicate the quality of the air.  
O. Fan Speed Indicator: Shows current fan speed setting (Turbo / High / Low / Quiet)  
.
P. Fan Speed Selector: Adjusts fan speed setting (Turbo / High / Low / Quiet)  
Q. On-Off: Turns the unit “On” and “Off.”  
.
R. Light Sensor: Dims the control panel lights and sets the fan speed to  
“Quiet” when the room is dark (only works when in “AUTO”).  
6
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 7  
AIR CLEANER SET-UP  
ELAP15, ELAP30  
Place the unit away from drafty areas, as the sensors may not react  
accurately. Do not place near curtains, furniture, or other items that  
might inhibit air flow. Place the unit on a stable surface.  
1. Remove protective film from the control panel.  
2. Remove the front panel by pulling gently from the top portion of  
the panel.  
3. Remove the HEPA filter and the Carbon Pre-Filter from the plastic  
wrapper.  
4. Install the HEPA filter with the arrow showing “air flow” pointing in toward  
the back of the air cleaner; the white tabs at the top and bottom of the  
HEPA filter will point out to the front of the unit.  
5. Install the Carbon Pre-Filter in front of the HEPA filter.  
6. Replace the front panel by hooking the panel on the bottom of the unit.  
7. Plug the power cord into a wall outlet.  
8. Press and hold the POWER button until a short “beep” sounds.  
9. The air cleaner will take 3-4 minutes to calibrate the air quality sensor.  
During this time the sensor lights will flash on and off. Once the sensor  
has calibrated, the lights will be on “AUTO” mode.  
7
Electrolux Customer Service 1-800-896-9756  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 8  
AIR CLEANER SET-UP  
ELAP40  
Place the unit away from drafty areas, as the sensors may not react  
accurately. Do not place near curtains, furniture, or other items that  
might inhibit air flow. Place the unit on a stable surface.  
1. Remove protective film from the control panel.  
2. Remove the front panel by pulling gently from the top portion of  
the panel.  
3. Remove the HEPA filter and the High Deodorization Anti-Odor Carbon  
Filter from the plastic wrapper.  
4. Install the HEPA filter with the arrow showing “air flow” pointing in toward  
the back of the air cleaner; the white tabs at the top and bottom of the  
HEPA filter will point out to the front of the unit.  
5. Install the High Deodorization Anti-Odor Carbon Filter in front of the  
HEPA filter.  
6. Replace the front panel by hooking the panel on the bottom of the unit.  
7. Plug the power cord into a wall outlet.  
8. Press and hold the POWER button until a short “beep” sounds.  
9. The air cleaner will take 3-4 minutes to calibrate the air quality sensor.  
During this time the sensor lights will flash on and off. Once the sensor  
has calibrated, the lights will be on “AUTO” mode.  
8
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 9  
AIR CLEANER SET-UP  
ELAP45  
Place the unit away from drafty areas, as the sensors may not react  
accurately. Do not place near curtains, furniture, or other items that  
might inhibit air flow. Place the unit on a stable surface.  
1. Remove protective film from the control panel.  
2. Remove the front panel by pulling gently from the top portion of  
the panel.  
3. Remove the Filter Cassette and remove the plastic wrapper  
from it.  
4. Install the Filter Cassette by gently sliding the entire cassette into  
the air cleaner. It should fit perfectly.  
5. Replace the front panel by hooking the panel on the bottom of the unit.  
6. Plug the power cord into a wall outlet.  
7. Press and hold the POWER button until a short “beep” sounds.  
8. The air cleaner will take 3-4 minutes to calibrate the air quality sensor.  
During this time the sensor lights will flash on and off. Once the sensor  
has calibrated, the lights will be on “AUTO” mode.  
9
Electrolux Customer Service 1-800-896-9756  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 10  
FILTER REPLACEMENT  
ELAP15, ELAP30  
ELAP40  
There are two separate filters:  
There are two separate filters:  
Carbon Pre-Filter and HEPA filter.  
High Deodorization Anti-Odor  
Carbon Filter and HEPA filter.  
Q The Check Filter indicator will signal when  
to replace the HEPA filter. The replace-  
ment period will vary depending on the  
hours of usage, air quality, and location  
of the unit. However, in most cases of  
normal use, the filter will need to be  
replaced annually.  
Q The Check Filter indicator will signal when  
to replace the HEPA filter. The replace-  
ment period will vary depending on the  
hours of usage, air quality, and location  
of the unit. However, in most cases of  
normal use, the filter will need to be  
replaced annually.  
Q For best performance, change the High  
Deodorization Anti-Odor Carbon Filter  
every 12 months. The filters should be  
disposed off when changed. Do not wash  
and reuse the HEPA filter or the High  
Deodorization Anti-Odor Carbon Filter as  
they will not work effectively.  
Q For best performance, change the Carbon  
Pre-Filter every three months.  
The filters should be disposed off when  
changed. Do not wash and reuse the HEPA  
filter or the Carbon Pre-Filter as they will  
not work effectively.  
!
CAUTION: Turn off the air cleaner  
!
CAUTION: Turn off the air cleaner  
and unplug the electrical cord before  
and unplug the electrical cord before  
performing any maintenance  
.
performing any maintenance  
.
Carbon Pre-Filter replacement  
1. Turn off the air cleaner and unplug the  
electrical cord.  
2. Remove the front panel by pulling gently  
from the lower portion of the panel. Do  
not force, the panel should remove  
easily.  
3. Remove the Carbon Pre-Filter by gently  
pulling out from the bottom and down  
from the top.  
High Deodorization Anti-Odor  
Carbon Filter replacement  
1. Turn off the air cleaner and unplug the  
electrical cord.  
2. Remove the front panel by pulling gently  
from the lower portion of the panel. Do  
not force, the panel should remove  
easily.  
3. Remove the High Deodorization Anti-  
Odor Carbon Filter by gently pulling out  
from the bottom and down from the top.  
4. Remove the Carbon Pre-Filter and  
4. Remove the High Deodorization Anti-  
dispose of it.  
Odor Carbon Filter and dispose of it.  
5. Remove a replacement Carbon Pre-Filter  
from the resealable plastic bag and  
reseal to maintain the freshness  
of the remaining filter.  
5. Remove a replacement High Deodoriza-  
tion Anti-Odor Carbon Filter from its  
plastic bag.  
6. Install the High Deodorization Anti-Odor  
61. In0stall the Carbon Pre-Filter.  
Carbon Filter.  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 11  
FILTER REPLACEMENT  
5. Remove the replacement filters from the  
ELAP45  
plastic bag and replace them.  
!
CAUTION: Turn off the air cleaner  
6. Replace the front panel by hooking the  
panel on the bottom of the unit.  
and unplug the electrical cord before  
performing any maintenance  
.
7. Plug in air cleaner and press POWER  
Filter  
Washable  
Cleancel®  
Pre-Filter  
Service life Cleaning Cycle  
How to clean  
button until short “beep” sounds.  
12 months Every 3  
Clean with vacuum  
months  
cleaner or soft  
8. Press the RESET FILTER button by  
gently inserting a paperclip into the  
RESET FILTER hole on the  
control panel. The light will  
flash 5 times before a  
brush. Use warm  
water when the  
filter is very dirty.  
Washable  
HEPA  
12 months Every 3  
months  
Soak the filter into  
warm water for 30  
minutes and dry it  
in the shade for  
24 hours.  
Soak the filter in  
warm water for 30  
minutes and dry it  
in the shade for  
24 hours.  
Filter set  
“beep” sounds to indicate  
the filter has been reset.  
Washable  
Anti-Odor  
Carbon  
Filter  
12 months Every 3  
months  
Filter  
12 months  
Cassette  
CARE AND MAINTENANCE  
ELAP15, ELAP30, ELAP40, ELAP45  
The Check Filter indicator will signal when  
to replace the Filter Cassette. The  
replacement period will vary depending on  
the hours of usage, air quality, and location  
of the unit. However, in most cases of  
normal use the filter will need to be  
!
CAUTION: Turn off the air cleaner  
and unplug the electrical cord before  
performing any maintenance  
.
replaced annually. This Filter Cassette  
should be disposed of when changed.  
Q Clean unit as necessary by wiping with a  
dry, soft cloth; for stubborn stains, use a  
warm, damp cloth.  
Filter Cassette replacement  
Q Do not use volatile fluids such as  
benzene, paint thinner or scouring  
powder, as they may damage the surface.  
Keep the unit dry.  
1. Turn off the air cleaner and unplug the  
electrical cord.  
2. Remove the front panel by pulling gently  
from the top portion of the panel.  
3. Remove the Filter Cassette by gently  
pulling out from the bottom and down  
from the top.  
Q Lightly vacuum air quality sensor  
every three months.  
4. Remove all the filters from the plastic  
frame and dispose of the filters only.  
Keep the frame.  
11  
Electrolux Customer Service 1-800-896-9756  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 12  
REMOTE CONTROL  
ELAP30, ELAP40, ELAP45  
Operate the remote control facing the air  
cleaner. Operate within 18 feet / 6 metres of  
the air cleaner. The remote control has a  
separate wall-mountable storage  
V. TURBO: Use this button to switch from  
automatic operation and start the  
maximum amount of room air cleaning  
and air movement. It will remain in Turbo  
speed until changed into Auto or  
manual mode.  
cradle that can be conveniently  
attached to any wall using a screw.  
S. POWER: Use the power button  
to turn the power on and off. A  
short “beep” will sound when  
the unit turns on and off.  
T. AUTO mode: Use the AUTO  
button to put air cleaner in  
AUTO mode.  
U. FAN SPEED: By pressing up or down,  
the unit will change fan speeds and enter  
into manual mode.  
Battery replacement  
1. Squeeze tabs of battery cover  
and at the same time pull cover  
out of remote.  
2. Insert battery as shown and  
close battery cover.  
3. Always use 3V lithium battery CR2025.  
Incorrect battery usage may cause  
battery fluid leakage and/or damage.  
Electrolux replacement parts  
Fits models  
Part number  
ELAP15  
EL041  
1 HEPA Filter and 4 Carbon Pre-Filters  
68691  
EL042  
68692  
EL043  
1 Filter Frame  
ELAP15  
1 HEPA Filter and 4 Carbon Pre-Filters  
1 Filter Frame  
ELAP30  
ELAP30  
1 HEPA Filter and 1 High Deodorization Anti-Odor Carbon Filter  
ELAP40, ELAP45  
1 Washable HEPA Filter Set, 1 Washable Anti-Odor Carbon Filter  
ELAP40, ELAP45  
ELAP40, ELAP45  
EL044  
68694  
and 1 Cleancel® Pre-Filter  
1 Filter Frame  
DISPOSAL  
Recycle the materials with the recycle  
symbol. Put the packaging in  
Do not dispose appliances marked  
with this symbol with household waste.  
Return the product to your local  
recycling facility or contact your municipal  
office.  
applicable containers to recycle it. Help  
protect the environment and human health  
and to recycle waste of electrical and  
electronic appliances.  
12  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 13  
TROUBLE SHOOTING  
ELAP15, ELAP30, ELAP40, ELAP45  
Occurrence  
Possible causes / solution  
Can I wash my filter?  
No, the filters that come with the unit will be ruined by water. Replace with new  
washable filter. (ELAP45 filters are washable.)  
Can I vacuum my filter?  
No, vacuuming will spread the dust back into the air. Replace with new filter. (ELAP45  
Washable Pre-Filter can be cleaned with a vacuum cleaner or soft brush.)  
There is an odor coming  
from my new unit.  
The unit has been concealed in a tightly wrapped package of corrugated cardboard  
and plastic. It may give off an odor; this should wear off in several days.  
Will this clean a bigger area CADR ratings are provided from a controlled testing environment, if that environment  
than what it is rated for?  
changes, it can affect the performance. If you have a slightly larger room than what the  
CADR rating is, it will help improve the air, but take longer.  
Where should I place  
the unit?  
Allow proper air circulation around the sides and in front of the unit. If there  
are doors or hallways it may reduce the airflow.  
The AIR QUALITY light  
is orange or red, but the  
air seems clean.  
• Clear the sensor with a vacuum cleaner, as it may be blocked or clogged.  
• Sometimes a can of compressed air may unclog the dust in the sensor.  
You can see dust in the air  
The unit will capture most dust and particles, however with opening doors, windows,  
central HVAC etc., there may still be some level of dust that you can see.  
or on my furniture.  
There is nothing holding the The filters are meant to rest inside the unit. Once the unit is turned on, the force of air  
filters in place.  
pulled through the machine will create a tight seal of the filters.  
I can hear revving of the  
This is normal, especially at night when all environmental sounds are quiet, you may  
fan motor.  
hear the motor running in repetition.  
The unit has stopped  
removing odors effectively,  
or is emitting an odor.  
• Make sure the air quality sensor is not blocked or clogged.  
• Move the unit closer to the offending odors.  
• Replace filters more frequently. They may have reached their capacity to absorb  
pollutants.  
The CHECK FILTER  
Press the RESET FILTER button by gently inserting a paper-clip into the  
RESET FILTER button hole. Hold for 3-5 seconds until a “beep” sounds to indicate the  
unit has been reset.  
indicator remains lit after  
replacing the HEPA filter.  
Can I turn off the sleep  
mode?  
No, but you can manually push to the fan speed you prefer which will stay at that  
speed until you change it.  
Unit makes a ticking sound. This is due to PlasmaWave® technology, it may come and go, but as long as the  
PlasmaWave® light is on, the function is working.  
The remote control  
does not work.  
• Make sure the remote control battery is inserted correctly.  
• Replace a worn-out battery.  
• Make sure that the remote control has a clear line of sight to the air cleaner.  
The air quality light is white, • Make sure the sensor is not blocked or clogged.  
but there is still dust/odor.  
• Replace the filter.  
The unit is running on high  
• Clear the sensor with a vacuum cleaner, as it may be blocked or clogged.  
all the time.  
• Sometimes a can of compressed air may unclog the dust in the sensor.  
The CHECK FILTER  
Press the RESET FILTER button by gently inserting a paper-clip into the  
RESET FILTER button hole. Hold for 3-5 seconds until a “beep” sounds to  
indicator remains lit after  
replacing the Filter Cassette. indicate the unit has been reset.  
13  
Electrolux Customer Service 1-800-896-9756  
 
airCleanerOG.qxp_AirFilter_English 1/20/14 12:05 PM Page 14  
SMALL DOMESTIC APPLIANCE WARRANTY  
Your appliance is covered by a one year  
limited warranty. For one year from your  
original date of purchase, Electrolux will repair  
or replace the appliance or parts, at  
DISCLAIMER OF IMPLIED  
WARRANTIES; LIMITATION OF  
REMEDIES:  
CUSTOMER’S SOLE AND EXCLUSIVE  
REMEDY UNDER THIS LIMITED WARRANTY  
SHALL BE, AT ELECTROLUX’S SOLE  
DISCRETION, PRODUCT OR PART REPAIR  
OR REPLACEMENT AS PROVIDED HEREIN.  
CLAIMS BASED ON IMPLIED WARRANTIES,  
INCLUDING WARRANTIES OF  
Electrolux’s option, that prove to be defective  
in materials or workmanship when the  
appliance is installed, used, and maintained in  
accordance with the provided instructions.  
Labor and all costs associated with returning  
the appliance or parts to us and our returning  
the appliance or parts to you are excluded  
under this warranty. As a matter of warranty  
policy, Electrolux will not refund the  
MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE, ARE LIMITED TO  
ONE YEAR OR THE SHORTEST PERIOD  
ALLOWED BY LAW. ELECTROLUX SHALL  
NOT BE LIABLE FOR CONSEQUENTIAL OR  
INCIDENTAL DAMAGES SUCH AS  
consumer’s purchase price. If a product or  
part under warranty is no longer available,  
Electrolux will replace with a comparable  
product of equal or greater value.  
PROPERTY DAMAGE AND INCIDENTAL  
EXPENSES RESULTING FROM ANY BREACH  
OF THIS WRITTEN LIMITED WARRANTY OR  
ANY IMPLIED WARRANTY. SOME STATES  
AND PROVINCES DO NOT ALLOW THE  
EXCLUSION OR LIMITATION OF INCIDENTAL  
OR CONSEQUENTIAL DAMAGES, OR  
LIMITATIONS ON THE DURATION OF  
IMPLIED WARRANTIES, SO THESE  
Exclusions: This warranty does not  
cover the following:  
1 Products with original serial numbers that  
have been removed, altered or cannot be  
readily determined.  
2 Products that have been transferred from  
the original owner to another party or  
removed outside the USA or Canada.  
3 Rust on the interior or exterior of the unit.  
4 Products purchased “as-is”.  
LIMITATIONS OR EXCLUSIONS MAY NOT  
APPLY TO YOU. THIS WRITTEN WARRANTY  
GIVES YOU SPECIFIC LEGAL RIGHTS. YOU  
MAY ALSO HAVE OTHER RIGHTS THAT  
VARY FROM STATE TO STATE.  
This warranty only applies to products  
purchased in the USA and CANADA. In  
the USA, your appliance is warranted by  
Electrolux Home Care Products, Inc. In  
Canada, your appliance is warranted by  
Electrolux Home Care Products Canada Inc.  
Electrolux authorizes no person to change  
or add to any obligations under this warranty.  
Product features or specifications as  
described or illustrated are subject to  
change without notice.  
5 Food loss due to product failure.  
6 Products used in a commercial setting or  
anything but single family household use.  
7 Labor or service visits under any  
circumstance.  
8 Glass parts or containers, filters, non-stick  
surfaces.  
9 Ordinary wear and tear.  
10 Damages caused by improper use,  
installation, or service; use of parts other  
than genuine Electrolux parts; negligence;  
abuse; misuse; inadequate or excessive  
power supply; accidents; fires; or acts of  
God.  
Keep your receipt or some other appropriate  
payment record to establish the warranty  
period. Should warranty service be required,  
you must show proof of purchase.  
USA  
1-800-896-9756  
Electrolux Home Care Products, Inc.  
10200 David Taylor Drive  
Charlotte, NC 28262  
CANADA  
1-800-896-9756  
If you need service:  
Electrolux Home Care Products Canada Inc.  
5855 Terry Fox Way  
To obtain warranty service in the USA or  
Canada, call 1-800-896-9756. Please have  
the model number, serial number, and date of  
Mississauga, ON, Canada L5V 3E4  
pu1rch4ase information available.  
 

Clarion Cassette Player AX430 User Manual
Cooper Lighting Indoor Furnishings 1800 24 User Manual
Cornelius Ice Maker CCM CCU User Manual
Cradlepoint Network Router MBR90 User Manual
Curtis MP3 Player MPK8854 User Manual
Delta Electronics Power Supply IPM C Series User Manual
Delta Electronics Power Supply Series E48SH User Manual
Faber Ventilation Hood Wall Mount Canopy Rangehood User Manual
GE Monogram Refrigerator ZFGP21HXSS User Manual
GE Washer EWA4500 User Manual